Instek GPS-3030DD 90W Single-Output Linear DC Power Supply with 0.39" Dual Digital LED screen, 30V DC, 3 Amp
On Sale Now! Save 10% on the Instek GPS-3030DD 90W Single-Output Linear DC Power Supply with 0.39'' Dual Digital LED screen, 30V DC, 3 Amp by Instek America Corp at Enria Industries. SKU: InsGPS-3030DD. MPN: GPS-3030DD. Hurry! Limited time offer. Offer valid only while supplies last. The Instek GPS-3030DD single-output linear DC power supply unit provides a constant source of DC voltage and current for powering and testing
The Instek GPS-3030DD single-output linear DC power supply unit provides a constant source of DC voltage and current for powering and testing electronic devices. The power supply unit (PSU) has one output that provides DC voltage up to 30V and current up to 3 amp. Potentiometer knobs on the unit's front panel allow for fine and coarse adjustment of the voltage and current output. Dual digital LED screens show voltage and current readings simultaneously and are readable in low light. The PSU features continuous or dynamic internal load selection for applications such as pulsed current. Terminals on the rear of the unit provide connection to an external device, such as a computer, for remote control. A power cord with a three-prong plug is included for connecting the PSU to a grounded outlet, and a test lead is included for testing applications. A built-in cooling fan helps prevent overheating, and overload protection and reverse polarity protection help prevent damage to the PSU and the device under test.
|Number of outputs||1|
|Maximum voltage and current output||Voltage: 30VDC; Current: 3 amp|
|Load regulation, + or – (percent of output + offset)||Less than or equal to 0.01% of voltage reading + 3mV (millivolts) when rating current is less than or equal to 3 amp; Less than or equal to 0.2% of current reading + 3mA (milliamp)|
|Line regulation, + or – (percent of output + offset)||Less than or equal to 0.01% of voltage reading + 3mV; Less than or equal to 0.2% of current reading + 3mA|
|Meter accuracy||+ or – (0.5% of reading + 2 digits)|
|Temperature coefficient||Less than or equal to 300 ppm per degree C|
|Recovery time||Less than or equal to 100 μs (microseconds) following a 50% load change with a minimum load of 0.5 amp|
|Ripple and noise (5Hz to 1MHz)||Less than or equal to 0.5mV RMS (root mean square) when rating current is less than or equal to 3 amp; Less than or equal to 1mV RMS when rating current is greater than 3 amp|
|Ripple current||Less than or equal to 3mA RMS|
|Power requirements||100V, 120V, 220V, 240VAC, + or – 10%, at 50 to 60Hz|
|Standards met||European Conformity (CE) marking|
|Dimensions||145 x 128 x 285mm (H x W x D)|
H is the vertical distance from lowest to highest point, W is the horizontal distance from left to right, and D is the horizontal distance from front to back.
Power supply units (also known as PSUs, AC power supplies, DC power supplies, and battery eliminators) provide AC or DC voltage to power or test devices such as tools, appliances, and electronic components. The PSU draws energy from a line source such as a wall socket and converts it to a constant, specified amount of voltage or current that is then outputted to a connected device. In general, a power supply unit will be classified as either a linear PSU (also known as a linear regulation or line-frequency PSU) or a switched PSU (also known as a switching-mode power supply, SMPS, or switcher). Typically, a linear PSU has a simpler design and provides a faster transient response time and less electrical interference and noise than a switched PSU. A switched PSU is often smaller, lighter, and more efficient than a linear PSU and generates less heat. The transient response time of a PSU indicates how quickly the PSU can resume the desired constant output after a sudden change in input. Ripple voltage or current indicates how much unfiltered noise and AC voltage or current is present at the output of a filtered power supply operated at full load. The temperature coefficient is the percent average change in output voltage per degree centigrade of change in ambient temperature. Fuses, current limiters, and other forms of overload protection can be built into the PSU to help protect against voltage spikes or short-circuiting.
GW Instek manufactures test and measurement equipment such as oscilloscopes, spectrum analyzers, signal testers, and video surveillance systems. The company, founded in 1975 and headquartered in Taipei, Taiwan, meets International Organization for Standardization (ISO) standards 9002 and 14001.
What's in the Box?
- Instek GPS-3030DD power supply unit
- (1) GTL-105 test lead
- Power cord
Features & Highlights
- Linear power supply unit provides a constant source of DC voltage and current for powering and testing electronic devices in research and development, production, and laboratory applications
- One output provides an adjustable voltage of up to 30VDC or current up to 3 amp
- Potentiometers on front panel provide fine and coarse adjustment of voltage and current output
- Dual digital LED screens show voltage and current readings simultaneously and are readable in low light
- Continuous or dynamic internal load selection for applications such as pulsed current
|Brand:||Instek America Corp|
|Item Weight:||12 pounds|
|Package Weight:||12.67 pounds|
|Package Size:||8.4 x 7.1 x 7.1 inches|